Article is in stock Repairtape ORATEX UL 600 for Schleicher EASA-AD 2021-0230 grey - length: 25 m

For further information please contact our ambassador Lars Gleitsmann from Better Aircraft Fabric via mail: [email protected].
There you will get full service and competent advice.

Description

ORATEX® UL 600 repair tape for Schleicher EASA-AD 2021-0230 According to Flight Manual Appendix 01-2021, an annual inspection of the elevator is required for these Schleicher aircraft: Ka6, K7, K8, ASK 13, ASK 16, ASK 18. To do this, the old covering in this area must be removed.

In order to avoid the expenses of a cotton covering with corresponding tautening dope and paint work, Schleicher has approved the use of ORATEX® UL 600 repair tape for the Schleicher EASA-AD 2021-0230 (16-xxx-030 / xxx is to be replaced by the colour code).


Technical data: • Width 30 mm • Length 25 m


Contents: The repair tape is supplied with a felt blade and fixing tape. • 1x ORATEX UL 600 repair tape • 1x ORATEX Felt blade - 10 x 14 cm • 1x ORATEX fixing tape - Width: 19 mm - Length: 50 m


Application: To restore the aircraft to airworthy condition after inspection or repair, proceed as follows: Iron the repair tape onto the back according to the diagram. Start at position 1 and iron the strip upwards to the top edge at a temperature of 90 degrees. The tape is then wrapped around the radius and overlaps by 1 cm on the back of the material that has already been ironed on. Next, the ORATEX fixing tape (order no. 08258) is stuck onto the fabric tape strip. The fixing tape is stuck on so that the edge of the fixing tape ends at the side of the curve. This serves to mark the end of the incisions. After cutting, the fixing tape is removed again and the repair tape is ironed around the curve as shown in the diagram, overlapping by 1 cm on the back. The incisions are ironed in a fan shape on the side of the curve and pressed down with the felt blade.

During a subsequent inspection, the repair tape can be removed again at 90 to 100 degrees, whereby an iron must not be used for this action, but rather a hot air blower, e.g. the Steinel HL 2020 E hot air blower (order no. 08470). The temperature on the digital display should be set to approx. 150 degrees so that approx. 90 to 100 degrees are applied to the object. Heat the tape thoroughly and pull it off slowly. Once you have loosened the first cm of the overlap, position the hot air gun so that the hot air hits the gap between the masking tape and the structure in order to soften the adhesive in a targeted manner and enable it to be removed.

For optimal viewing of the video in the best possible image quality, please click on the cog icon and select the 1080p resolution.

✔


Information on product safety:

Manufacturer: LANITZ-PRENA Folien Factory GmbH, Am Ritterschlösschen 20, 04179 Leipzig, Germany, [email protected]

Question to this article

Please enter your question and we will response immediately

Legal notice:

* Our offer is aimed at final consumers. Therefore, all quoted prices include 19 % German VAT. Transport costs will be charged on top of that.

Pictures may differ from the original products. We cannot assume any liability for the product information given. Accessories shown in the pictures are not included in the delivery. The trademarks mentioned on this website and in our advertising materials, e.g. ORACOVER, ORASTICK, ORALIGHT, ORALINE, ORATRIM, EASYCOAT, EASYPLOT, ORATEX, CARBON are registered trademarks, the use of which is reserved exclusively to Lanitz Prena Folien Factory. All other logos, descriptions and trademarks are property of the respective manufacturer. Subject to change and prior sale. Errors excepted.

Lade ...